英语翻译8.每天停机时(如胶辊和进纸钢辊是全接触使用)则先关闭液泵开关,几分种后当胶辊上没有淋膜液了即可停机.并松开胶辊

英语翻译
8.每天停机时(如胶辊和进纸钢辊是全接触使用)则先关闭液泵开关,几分种后当胶辊上没有淋膜液了即可停机.并松开胶辊和所有接触钢辊间的压力.
特别注意：不用机器时必须松开调节钢辊和胶辊间压力,如果进纸钢辊和胶辊接触在一起.也要将胶辊升起来,以免胶辊单边长时间受压变形!
9.UV灯在开关打开后五分钟才能正常工作.UV灯关闭后等五分钟才能打开,启动时先开UV灯,再开冷却风机.并且将UV冷却风机调到较弱这样UV灯才能在几分钟内亮起来.等到UV灯亮起来以后再将UV冷却风机调到稍强.(具体根据环境温度来调节大小,但最好不要将UV冷却风机调到最强处,以免长时间使用影响风机寿命).每天尽量集中在一起淋膜.发生粘片现象时必须及时退片,以免卷在机器里无法取出.
10长时间不用或胶辊上有灰尘,杂质时需用无水酒精和白丝绸清洗胶辊和调节钢辊表面.并要松开调节钢辊使之和胶辊不紧密接触.
11清洗时注意让调节钢辊离开胶辊,不要让丝绸布卷入胶辊造成人为损坏.最好清洗时停机.
12最好用随机送的过滤布包住出液口（剪一小块用扎带缠紧）,过一定时间就更换,这样可以避免淋膜液里面混进杂物,损伤淋膜胶辊或影响淋膜质量.
13如UV输送带持续单边跑边,可稍调松机器后部的调节把手,让纠偏辊能起作用即可!
14.UV固化机左边红色的旋纽开关是UV光强度档位调节,按标识分别是弱,强二档.出厂设定在强的挡位.可开机任意换档.启动时也必须在强档.
等待时可调到弱档以节电..
15．如淋膜时机器胶棍或进纸辊出现发抖或时停时走现象,请检查各个链轮,齿轮上的锁紧键是否有松动.
16.本机采用屏蔽了紫外线设计,经专业的设备测试,机器外紫外线强度远小于太阳光中的紫外线强度,.(注:紫外线为不可见光,肉眼是看不见的,发出的白光并不是紫外线)

8. When shutdown (such as steel roller and feed rollers are Keys to use) then turn off the pump switch, a few minutes later, when there is no lamination roller liquid has to stop. And release the roller and all Contact pressure between steel rollers. Special Note: do not adjust the machine must be released between the steel roller and pressure roller, steel roller, and if the feed roller contacts together. but also to rise up roller, rubber roller to avoid unilateral time pressure deformation!
9.UV lights five minutes after the switch is turned to work properly. UV light is off after the five minutes to open, start the first open UV light, and then open the cooling fan. UV cooling fan and will be transferred to such a weak UV lamp to light up within minutes. Up until after the UV light and then transferred to the cooling fan slightly stronger UV. (To adjust the temperature according to the specific size, but best not to be transferred to the strongest at UV cooling fan, fan life so as not to affect long-term use) every day as Laminating together. Sticky film phenomenon occurs when the eject must be timely, so as not to roll in the machine can not be removed.
10.If for a long time or do not have dust, impurities, when required anhydrous alcohol and white silk cleaning roller and adjustable steel roller surface.
11. And to release the adjusted steel rollers and roller does not make close contact. Note to adjust the cleaning roller steel roller to leave, do not let the silk cloth roller involved in causing human damage. You'd better clean downtime.
12. It's the best random sent to live out the liquid outlet filter cloth (cut a small piece of wrapped tightly with cable ties), over a certain time to replace, to avoid entering into the debris inside the liquid lamination, plastic laminating roller or damage affect the lamination quality.
13.Continuous conveyor belt as a single UV leak, loosen the rear of the machine can be a little adjustment handle, so that correction can roll that can work!
14.UV curing unit on the left is the red knob switch gear UV light intensity adjustment, Click logo are weak, strong second gear. Factory set at strong gear. Can start any gear. Must also start thing as.
15. Adjustable wait to file for saving the weak . Laminating machines, such as glue stick, or when the paper feed roller when there shivering or stop-and-go phenomenon, check each sprocket, gear lock key is on the loose.
16.16 The machine designed to shield the ultraviolet, through the professional equipment to test the machine outside the UV intensity is much smaller than the sun's ultraviolet intensity. (Note: for non-UV-visible light, invisible to the naked eye, white is not the issue UV)
希望能帮到你,祝更上一层楼O(∩_∩)O
有不会的欢迎再继续问我(*^__^*)