作业帮 > 英语 > 作业

英语翻译This unusual design is shown here sa a mirror frame,but

来源:学生作业帮 编辑:作业帮 分类:英语作业 时间:2024/05/25 05:16:14
英语翻译
This unusual design is shown here sa a mirror frame,but a similar frame could just as easily be used to frame aphotograph or favourite picture.Only two colours are used,although the grouting is a third element.
1.Cut a sheet of plywood measuring 50x70cm(20x80in)with a jingsaw(saber saw).uaing a large brush,prime the wood by coating it all over with diluted PVA(white)glue.leave it to dry for 24 hours.
2.Place two blue tiles face down on a dishtowel and fold over the edges.Using a hammer,smash the tiles repeatedly,checking from time to time until they are roughly broken into manageable fragments,keeping the blue and black pieces in separate piles.
3.Draw around the plywood sheet on a large sheet of tracing paper,then draw an inner rectangle of 39x60cm(16x24in).Sketch one scroll design on the tracing paper,then use sheets of carbon papar to transfer your design onto the plywood,flipping the tracing paper to repeat a mirror image another five times.Go over with a thick pen.
4.Mix some tile adhesive with admix,then spread it 3mm(1/8in)thick over a small section of one of the scrolls,removing any excess.Working from the scroll edge out,fill in the blue tiles,and repeat until the frame is covered.Allow 24 hours for the adhesive to dry.
5.Spread some tile grout over the mosaic with a rubber spreader,using a circular motion.Continue until the grout fills all the gaps and is level with the tesserae.Sponge away any surface grout with a damp sponge.Allow to dry for 1 hour,then polish with a dry,soft cloth to rub off any residual grout.Glue the mirror in place.
这个异常的设计显示这里sa一个镜子框架,但是一个相似的框架可能正容易地被用于构筑aphotograph或喜爱图片.仅使用二种颜色,虽然填水泥是第三个元素.1.Cut测量50x70cm (20x80in)与jingsaw (军刀锯) .uaing的胶合板板料一把大刷子,通过涂它填装木头到处用被稀释的PVA (白色) glue.leave它烘干24个小时.2.Place二蓝色瓦片在dishtowel面对下来并且重叠边缘.使用锤子,抽杀一再瓦片,时常检查,直到他们是大致残破的入易处理的片段,保留蓝色和黑片断在分开的堆.在胶合板板料附近的3.Draw在描图纸一大张,然后得出一个内在长方形39x60cm (16x24in).剪影一在描图纸的纸卷设计,然后使用papar碳的板料转移您的在胶合板上的设计,翻转描图纸重复镜象另外五次.越过与一支厚实的笔.一些瓦片胶粘剂与浓厚混合的4.Mix,然后传播它3mm (1/8in)在一个小部分其中一个纸卷,去除所有剩余.工作从纸卷替代,填写蓝色瓦片,并且重复,直到框架报道.允许胶粘剂的24个小时能烘干.5.Spread在马赛克的一些瓦片水泥与橡胶分布器,使用一种圆周运动.继续,直到水泥填补所有空白并且是级与tesserae.擦与一块潮湿海绵的所有表面水泥.让烘干1个小时,然后擦亮以一块干燥,软的布料消除所有残余的水泥.胶合到位的镜子.