作业帮还有一点.机械专业英语怎么翻译下面的文章?跪求达人.
来源：学生作业帮 编辑：作业帮 分类：英语作业 时间：2024/05/14 19:06:49
还有一点.机械专业英语怎么翻译下面的文章?跪求达人.
1.1. Piloting
Piloting is one of the essential activities in strip layout design for progressive dies. The strip must be positioned accurately in each station so that the operations are performed at the proper locations.
Generally, there are three kinds of piloting in progressive dies. When one or two circular holes of the part are used for piloting they are called direct pilots. When one or two circular holes are created in the scrap area and used for piloting they are called indirect pilots. When circular holes are created inside the noncircular holes of the part for piloting purposes and in the last station, the entire holes are punched into the desired shape they are called semi-direct pilots.
A hole is considered to be suitable as a pilot hole if it is circular and Its diameter is greater than an allowable minimum diameter. If the diameter of the pilot is not large enough it can easily be deflected or even broken during operation. The pilot hole also should be located far enough from other holes of the workpiece. If the scrap area is used for indirect piloting, the amount of increase in strip width should be minimum.
1.1. Piloting
Piloting is one of the essential activities in strip layout design for progressive dies. The strip must be positioned accurately in each station so that the operations are performed at the proper locations.
Generally, there are three kinds of piloting in progressive dies. When one or two circular holes of the part are used for piloting they are called direct pilots. When one or two circular holes are created in the scrap area and used for piloting they are called indirect pilots. When circular holes are created inside the noncircular holes of the part for piloting purposes and in the last station, the entire holes are punched into the desired shape they are called semi-direct pilots.
A hole is considered to be suitable as a pilot hole if it is circular and Its diameter is greater than an allowable minimum diameter. If the diameter of the pilot is not large enough it can easily be deflected or even broken during operation. The pilot hole also should be located far enough from other holes of the workpiece. If the scrap area is used for indirect piloting, the amount of increase in strip width should be minimum.
1.驾驶
驾驶是一个在级进模排样设计的基本活动.条必须准确定位在每一站,在适当的位置进行操作.
一般来说,有三种在级进模中驾驶.当一个或两个圆形孔的部分用于引导他们被称为直接的飞行员.当一个或两个圆形孔是在废料区域创建和使用他们称为间接飞行员驾驶.当圆形孔内创建的部分的非圆形孔控制的目的和最后一站,整个打孔成所需的形状,它们被称为半直接的飞行员.
一个孔被认为是合适的如果它是圆形,其直径大于允许的最小直径为先导孔.如果飞行员的直径是不足够大,它可以很容易地变形甚至折断术.先导孔也应位于足够远从工件孔.如果废区用于间接引导,在条带宽度的增加量应最小.
驾驶是一个在级进模排样设计的基本活动.条必须准确定位在每一站,在适当的位置进行操作.
一般来说,有三种在级进模中驾驶.当一个或两个圆形孔的部分用于引导他们被称为直接的飞行员.当一个或两个圆形孔是在废料区域创建和使用他们称为间接飞行员驾驶.当圆形孔内创建的部分的非圆形孔控制的目的和最后一站,整个打孔成所需的形状,它们被称为半直接的飞行员.
一个孔被认为是合适的如果它是圆形,其直径大于允许的最小直径为先导孔.如果飞行员的直径是不足够大,它可以很容易地变形甚至折断术.先导孔也应位于足够远从工件孔.如果废区用于间接引导,在条带宽度的增加量应最小.
还有一点.机械专业英语怎么翻译下面的文章?跪求达人.
机械专业英语怎么翻译下面的文章?跪求达人.
求文章翻译，专业一点的，最好人工翻译
哪位英语专业或者懂得能来帮我翻译一下下面这段文章，道路桥梁专业的专业英语翻译成中文，还会加分的！
英语翻译请机械专业英语高手帮我把下面这段话翻译成机械英语,不要用狗狗在线翻译或者翻译软件分析结果表明,力矩马达的线性度主
英语翻译麻烦英语高手帮小弟翻译下面文章,用机械翻译的就不要搞我了!
求人工翻译一小段话,较复杂,机械方面的专业英语.
求翻译,机械的专业英语 在线等,合适有高分送
机械专业英语在线翻译，在线等，不要软件翻译，谢谢
求助专业汽车英语怎么翻译
请牛人翻译下面的英语文章?
帮我翻译一下下面的文章,要通顺（大学英语）.翻译的好了定重谢...最好快一点