作业帮求翻译,翻译帝、翻译后们,请用你们光芒掩埋我吧!
来源：学生作业帮 编辑：作业帮 分类：综合作业 时间：2024/05/13 02:18:24
求翻译,翻译帝、翻译后们,请用你们光芒掩埋我吧!
NOTE:UNLESS OTHERWISE STATED THE FOLLOWING APPLIES:
1 ISO 5456-2 METHOD 3 PROJECTION.
2 S.I.UNITS TO TRW TS1-20-092.
3 TOLERANCING TO ISO 1101/DIN 7167.
4 SURFACE ROUGHNESS TO ISO 1302.
5 DIMENSIONS APPLY ON FINISHED COMPONENT INCLUDING SURFACE TREATMENT.
6 ABBREVIATIONS TO TRW TS1-10-001.
7 WELD SYMBOLS TO DIN 1912-4.
8 D DATUM DIMENSIONS.
9 METRIC THREADS TO DIN 13.
10 UNIFIED INCH THREADS TO ASME B1.1.
11 MATERIAL RELEASE TO TRW TS1-15-026,CONTROL OF PROHIBITED &
RESTRICTED SUBSTANCES TO TRW B_080_3_01_EN.
12 EDGES OF WORKPIECES TO ISO 13715.
13 BLACK DOT INDICATES MODIFICATIONS TO THE PREVIOUS DRAWING REVISION.
14 KEY CHARACTERISTICS TO TRW C_045_BRK_3_002_289_EN.
PROTECTION NOTICE TO ISO 16016:
THE REPRODUCTION,DISTRIBUTION AND UTILIZATION OF THIS DOCUMENT
AS WELL AS THE COMMUNICATION OF ITS CONTENTS TO OTHERS WITHOUT
EXPRESS AUTHORIZATION IS PROHIBITED. OFFENDERS WILL BE HELD LIABLE
FOR THE PAYMENT OF DAMAGES. ALL RIGHTS RESERVED IN THE EVENT OF THE
GRANT OF A PATENT,UTILITY MODEL OR DESIGN.
KEY CHARACTERISTICS:TS3-98-179
机械制图上的技术要求,翻译帝、翻译后们,请用你们光芒掩埋我吧!
PS：没有积分了. - -!
NOTE:UNLESS OTHERWISE STATED THE FOLLOWING APPLIES:
1 ISO 5456-2 METHOD 3 PROJECTION.
2 S.I.UNITS TO TRW TS1-20-092.
3 TOLERANCING TO ISO 1101/DIN 7167.
4 SURFACE ROUGHNESS TO ISO 1302.
5 DIMENSIONS APPLY ON FINISHED COMPONENT INCLUDING SURFACE TREATMENT.
6 ABBREVIATIONS TO TRW TS1-10-001.
7 WELD SYMBOLS TO DIN 1912-4.
8 D DATUM DIMENSIONS.
9 METRIC THREADS TO DIN 13.
10 UNIFIED INCH THREADS TO ASME B1.1.
11 MATERIAL RELEASE TO TRW TS1-15-026,CONTROL OF PROHIBITED &
RESTRICTED SUBSTANCES TO TRW B_080_3_01_EN.
12 EDGES OF WORKPIECES TO ISO 13715.
13 BLACK DOT INDICATES MODIFICATIONS TO THE PREVIOUS DRAWING REVISION.
14 KEY CHARACTERISTICS TO TRW C_045_BRK_3_002_289_EN.
PROTECTION NOTICE TO ISO 16016:
THE REPRODUCTION,DISTRIBUTION AND UTILIZATION OF THIS DOCUMENT
AS WELL AS THE COMMUNICATION OF ITS CONTENTS TO OTHERS WITHOUT
EXPRESS AUTHORIZATION IS PROHIBITED. OFFENDERS WILL BE HELD LIABLE
FOR THE PAYMENT OF DAMAGES. ALL RIGHTS RESERVED IN THE EVENT OF THE
GRANT OF A PATENT,UTILITY MODEL OR DESIGN.
KEY CHARACTERISTICS:TS3-98-179
机械制图上的技术要求,翻译帝、翻译后们,请用你们光芒掩埋我吧!
PS：没有积分了. - -!
补上图片
注意：技术要求按如下除非另有说明
1.ISO 5456-2第三角画法
2.S.I单位按TRW TS1-20-092
3.公差按ISO 1101/DIN 7167
4.表面粗糙度按ISO 1302
5.尺寸为已完工部件（包括表面处理）尺寸
6.缩写按TRW TS1-10-001
7.焊接符号按DIN 1912-4
8.D 表示资料尺寸
9.公制螺纹按DIN 13
10.统一的英制螺纹按ASME B1.1
11.材料使用按TRW TS1-15-026,违禁物质的控制按TRW B_080_3_01_EN
12.工件边缘按ISO 13715
13.黑点表明是上次图纸版本的改动
14.关键特性按TRW C_045_BRK_3_002_289_EN
按ISO16016的保护注意事项:
未经特别授权禁止对本文件的内容进行复制、分发、使用以及与他人进行交流.违者将赔偿损失.专利,型号或设计的授权保留所有权利.
关键特性按TS3-98-179
1.ISO 5456-2第三角画法
2.S.I单位按TRW TS1-20-092
3.公差按ISO 1101/DIN 7167
4.表面粗糙度按ISO 1302
5.尺寸为已完工部件（包括表面处理）尺寸
6.缩写按TRW TS1-10-001
7.焊接符号按DIN 1912-4
8.D 表示资料尺寸
9.公制螺纹按DIN 13
10.统一的英制螺纹按ASME B1.1
11.材料使用按TRW TS1-15-026,违禁物质的控制按TRW B_080_3_01_EN
12.工件边缘按ISO 13715
13.黑点表明是上次图纸版本的改动
14.关键特性按TRW C_045_BRK_3_002_289_EN
按ISO16016的保护注意事项:
未经特别授权禁止对本文件的内容进行复制、分发、使用以及与他人进行交流.违者将赔偿损失.专利,型号或设计的授权保留所有权利.
关键特性按TS3-98-179