英语翻译Describing the operation panel:1.EMERGENCY STOP the EMER

英语翻译
Describing the operation panel:
1.EMERGENCY STOP the EMERGENCY STOP button is red and is located in the lower left corner of the control panel.If this button is pressed,the feed and rotation of the tool is stopped and the control system of the computer is turned off.The EMERGENCY STOP button is only used in special situations.To reset the EMERGENCY STOP button,push it in and turn it clockwise.Then you can turn the machine on,zero it,and eliminate the cause that forced the use of the EMERGENCY STOP button.
2.MODE SELLECT Use this switch to specify the operational mode.
3.EDIT positioning the switch in the EDIT mode enables you to:
Enter the program to machine memory
Enter any changes to the program
Transfer data from the program to a tape
Check the memory storage capacity
4.MEMORY Positioning the switch in the MEMORY mode enables the NC commands stored in the memory to be executed.
5.MDI positioning the switch in the MDI mode enables the automatic control of the machine.MDI can also be used during the execution of the program.For example,suppose you have omitted the command s350 m03 in the program.In order to correct this omission,turn on the SINGLE BLOCK switch and the position selector switch to the MDI mode.Using MDI,you can enter functions s350 and m03.Enter this command through INPUT and START.
6.HANDLE positioning the switch in the HANDLE mode allows for the manual control of the movements of the table with the use of the handwheel,along one of four axes:X,Y,Z,or B.by turning the handwheel clockwise,you can displace the tool in a positive direction with respect to the position of the coordinate system.By turning the handwheel counterclockwise,the tool is displaced in a negative direction with respect to the position of the coordinate system.When the switch is positioned at
×1:Turning the wheel by one unit corresponds to the displacement of 0.0001 in.
×10:Turning the wheel by one unit corresponds to the displacement of 0.001 in.
×100:Turning the wheel by one unit corresponds to the displacement of 0.01 in.
7.JOG setting the selector switch in the JOG mode allows the selection of manual monotonous feeds along the x,y,and z axis.
8.CYCLE START Use this button during the execution of the program from MEMORY or TAPE.When the CYCLE START button is pressed,the control lamp located above this button goes on.

描述的操作面板：
1.停止紧急停止按钮,紧急情况是红色,并在较低的控制面板位于左上角.如果这个按钮按下时,饲料和工具的旋转停止,计算机控制系统处于关闭状态.紧急停止按钮只有在特殊情况下使用.要重置紧急停止按钮,按下它,把它旋转.然后你可以打开机器上,零它,并消除,迫使有关当局紧急停止按钮的使用原因.
2.模式SELLECT使用此开关来指定操作模式.
3.编辑定位在编辑模式开关使您能够：
输入程序机内存
输入该程序的任何变化
从程序的数据传输到磁带
检查内存的存储容量
4.内存定位在内存模式开关使数控指令存储在内存中被执行.
5. MDI的定位在MDI模式的切换,使机器的自动化控制. MDI的也可用于在程序的执行.例如,假设你有遗漏了在程序命令s350 m03.为了纠正这种不作为,在单块开关和选择开关的位置对MDI模式转变.使用的MDI,您可以输入功能s350和m03.通过输入此INPUT和START命令.
6.拉手定位在拉手模式开关允许与手轮的使用表的运动手动控制,由手轮顺时针转动,可以取代四沿一轴：的X,Y,Z或乙与方面的坐标体系中的地位工具朝着积极的方向.通过手轮逆时针转动,该工具是流离失所者在消极的方向发展方面的坐标体系中的地位.当开关定位于
× 1：将一个单位的车轮对应0.0001英寸位移
× 10：将一个单位的车轮对应0.001英寸位移
× 100：将一个单位的车轮对应0.01英寸位移
7.飞梭设置在飞梭模式选择开关允许人工选择沿单调的x,y供稿和z轴.
8.周期开始使用期间从内存或胶带程序执行这个按钮.周期开始时,按下按钮,控制灯高于此按钮,位于下去.